How to Remove as Well as Replace a Bath Tub
How to Remove as Well as Replace a Bath Tub
Blog Article
This post listed below on the subject of A Step-by-Step Guide to Installing a Bathtub is exceptionally enlightening. Check it out for yourself and see what you think about it.
Setting up a tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily obtainable, the project can move speedily; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the task is a lot harder. In either instance, the task is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Make certain you have actually certified on your own for the task as well as fit trying it. As opposed to working with a specialist to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Possibilities are you may need an expert plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have already bought a new bathtub and also don't need to change the setup of your previous water system pipelines.
Your tools as well as material checklist need to make up the following:
Preparing for the Installation
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to stop stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its last setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, activate the taps to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be rather troublesome as a result of the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Before going on to fit the new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Making use of the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub up until the level checks out degree.
To install faucets, fit the bottom of the furthest flexible tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the supply of water and inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub as well as likewise inspect the overflow outlet and the normal outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and also sealing around the bathtub should wait up until the bathtub has been made use of a minimum of once as this will certainly resolve it right into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind should be attached to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall between the bathroom and the tiling, bring about complications with wetness and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and cartridges, and are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealant can break rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the tiles making use of water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
We were made aware of that report about How to Install a Bathtub from a good friend on our other web property. Sharing is nice. You never know, you will be helping someone out. Thank-you for going through it.
Schedule A Free Estimate
Report this page